ECX Ruckus ECX03003I Manuel d'instructions télécharger pdf (Page 10)

RUCKUS

SHOCK CLEANING

Oil-ﬁ lled shocks will require regular maintenance due to the

oil breaking down or getting dirty. This maintenance should be

performed after about every 3 to 5 hours of use, depending on

the conditions that the vehicle is used in.

• Remove the shock from the vehicle.

• Remove the cap from the shock body and dispose of fluid.

• Disassemble the shock. Clean thoroughly with DYN5505. Dry

parts before assembly.

• Re-assemble the shock and refill the shock body with silicone

fluid (30 weight recommended).

• Slowly move the shaft and piston up and down to remove air

bubbles.

• Move the piston to the midway point of the body and install

the cap.

• Wipe off any overflowing fluid.

• When properly filled, the piston should rebound about 3/8 in

(9.5mm) after being pushed in fully.

• Re-install the shock on the vehicle.

Ride Height Adjustment

Ride height is an adjustment that affects the way the vehicle

jumps, turns and goes over bumps. Drop one end of the

vehicle from approximately 6 inches (152 mm) in height onto

a ﬂ at surface. When dropping the front of the vehicle, after

the vehicle settles, make sure the front arms are equal and

parallel to the ﬂ at surface. Do the same with the rear to make

sure both arms are parallel with the ﬂ at surface.

Lowering the front ride height increases steering, but

decreases traction. Lowering the rear ride height increases

traction, but decreases steering.

Part # Description

ECX1036 Shock Body Set

ECX1037 Shock Caps, Pistons

ECX1038 Shock Parts Set

ECX1039 Front Shock Shaft (2)

ECX1040 Rear Shock Shaft (2)

ECX1041 Front Shock Springs (2)

ECX1042 Rear Shock Springs (2)

ECX1043 Shock O-Ring Set

No. Description

TAPPING

BINDER HEAD

M3x10mm

TAPPING

BINDER HEAD

M3x12mm

TAPPING

FLAT HEAD

M3x15mm

TAPPING

FLAT HEAD

M3x12mm

TAPPING

FLAT HEAD

M3x10mm

TAPPING

BINDER HEAD

M3x18mm

TAPPING

FLAT HEAD

M2x16mm

TAPPING

BINDER HEAD

M3x16mm

No. Description

WASHER

5x7x0.5mm

E-CLIP E2.5

LOCK WASHER

FLANGED

LOCK NUT M4

WASHER

3x8x0.5mm

LOCK NUT M3

WASHER

2x7x0.5mm

SET SHAFT

SCREW

M3x13mm

No. Description

SETSCREW

M3x3mm

SETSCREW

M3x12mm

STEP SCREW

M3x0.5x13.4mm

STEP SCREW

M3x0.5x10.5mm

BUTTON

HEX

M2.5x4mm

BUTTON

HEX

M2.5x8mm

STEP SCREW

M3x0.5x7.4mm

No. Description

BINDER

HEAD

M3x8mm

BINDER

HEAD

M3x12mm

BINDER

HEAD

M3x20mm

BINDER

HEAD

M3x25mm

REAR SHOCK FRONT SHOCK

ECX1043

ECX1037

ECX1041

ECX1037

ECX1043

ECX1036

ECX1038

ECX1043

ECX1037

ECX1038

ECX1042

ECX1040

ECX1057

ECX1037

ECX1043

ECX1038

ECX1039

ECX1036

ECX1038

ECX1037

ECX1057

FASTENERS

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

ECX Ruckus ECX03003I Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Véhicules-jouets ECX Ruckus ECX03003I