ECX Circuit ECX03000 Manuel d'instructions télécharger pdf (Page 3)

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with

a combination of waterproof and water-resistant components to

allow you to operate the product in many “wet conditions”, including

puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely

waterproof and your vehicle should NOT be treated like a submarine.

The various electronic components used in the vehicle, such as the

Electronic Speed Control (ESC), servo(s) and receiver are waterproof,

however, most of the mechanical components are water-resistant

and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as

well as the contacts in the electrical cables, will be susceptible to

corrosion if additional maintenance is not performed after running in

wet conditions. To maximize the long-term performance of your ve-

hicle and to keep the warranty intact, the procedures described in the

“Wet Conditions Maintenance” section below must be performed

regularly if you choose to run in wet conditions. If you are not willing

to perform the additional care and maintenance required, then you

should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this

product and complying with the following precautions

could result in product malfunction and/or void the warranty.

General Precautions

• Read through the wet conditions maintenance procedures

and make sure that you have all the tools you will need to

properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the

battery manufacturer before use. Caution should be taken

when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your

transmitter’s manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may

be present.

• Do not operate your vehicle where it could come in contact

with salt water (ocean water or water on salt-covered roads),

contaminated or polluted water. Salt water is very conductive

and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor

if it has not been certified as water-resistant or waterproof. If

the motor becomes excessively wet, apply very light throttle

until the water is mostly removed from the motor. Running a

wet motor at high speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The

additional resistance of operating in water causes excess

strain. Alter the gear ratio by using a smaller pinion or larger

spur gear. This will increase torque (and motor life) when

running in mud, deeper puddles, or any wet conditions that will

increase the load on the motor for an extended period of time.

Wet Conditions Maintenance

• Drain any water that has collected in the tires by spinning

them at high speed. With the body removed, place the vehicle

upside down and pull full throttle for a few short bursts until

the water has been removed.

CAUTION: Always keep hands, ﬁ ngers, tools and any

loose or hanging objects away from rotating parts when

performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an

air compressor or a can of compressed air, blow out any water

that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the

mud and dirt off with a garden hose. Avoid rinsing the bearings

and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the

vehicle and help remove any water that may have gotten into

small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal

parts with a water-displacing light oil or lubricant. Do not

spray the motor.

• Let the vehicle air dry before you store it. Water (and oil)

may continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and

lubrication of the following:

• Front and rear axle hub assembly bearings.

• All transmission cases, gears and differentials.

• Motor—clean with an aerosol motor cleaner and re-oil

the bushings with lightweight motor oil.

Transmitter

Frequency 2.4GHz

Modulation DSM, DSM2, DSMR, Marine

Battery AA x 4

Servo

Power Supply 4.8V~6V (shared with receiver)

Output Torque 41.66 oz (3 kg-cm)

Operating Speed 0.23sec/60 degrees of travel

Size 55.6 x 18 x 30mm

Electronic Speed Control (ESC)

Input Voltage 6.0–8.4 V

Electric Capacity (FET) Forward 40A/180A

Electric Capacity (FET) Reverse 20A/90A

PWM Frequency 1kHz

BEC Voltage 5V/2A

Size 36 x 31.7 x 18mm

Weight 65 g

SPECIFICATIONS

1 2 3 4 5 6 7 8 ... 18 19

Commentaires sur ces manuels

Pas de commentaire

ECX Circuit ECX03000 Manuel d'instructions Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Véhicules-jouets ECX Circuit ECX03000